滑油量对恒速传动装置的影响

本文介绍了中外航空公司飞机发动机恒速传动装置几个故障典例及造成的危害,分析了填加滑油量不当对发动机恒速传动装置的影响,提出了预防措施。     

高频大电压标准器

主要阐述了该标准器的基本原理,从理论上对结构补偿法进行了分析和数学推导,当R/Z_o=1.9～2.0之间时,具有最小的交直流差。设计了匹配的同轴热电转换标准器;进行了误差分析;给出了试验结果,说明该标准器交直流差的重复性和复现性是好的。     

弧焊电源动态特性测试方法的研究

本文对弧焊特性、特别是它的动特性进行了讨论，与过去传统的时域法不同，文中提出了用频域法分析弧焊的电源特性的设想，文内中方法的理论、实验方法及实测结果进行了讨论。     

Spatial transformation of general sampling-aliasing frequency region for rotating-blade parameter identification with emphasis on single-probe blade tip-timing measurement

Blade-health monitoring is intensely required for turbomachinery because of the high failure risk of rotating blades. Blade-Tip Timing (BTT) is considered as the most promising technique for operational blade-vibration monitoring, which obtains the parameters that characterize the blade condition from recorded signals. However, its application is hindered by severe undersampling and stringent probe layouts. An inappropriate probe layout can make most of the existing methods invalid or inaccurate. Additionally, a general conflict arises between the allowed and required layouts because of arrangement restrictions. For the sake of economy and safety, parameter identification based on fewer probes has been preferred by users. In this work, a spatial-transformation-based method for parameter identification is proposed based on a single-probe BTT measurement. To present the general Sampling-Aliasing Frequency (SAFE) map definition, the traditional time–frequency analysis methods are extended to a time-sampling frequency. Then, a SAFE map is projected onto a parameter space using spatial transformation to extract the slope and intercept parameters, which can be physically interpreted as an engine order and a natural frequency using coordinate transformation. Finally, the effectiveness and robustness of the proposed method are verified by simulations and experiments under uniformly and nonuniformly variable speed conditions.     

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.      

带气膜阻尼结构振动特性的理论研究

针对航空发动机气膜阻尼的结构设计需求,基于挤压间隙流理论和能量方程建立气膜阻尼的力学模型,由此获得气膜阻尼结构的等效刚度系数和等效阻尼系数,通过振动方程的理论推导获得放大因子的表达式.结果表明:气腔厚度、气腔初始压强、吸振薄板模态频率和安装位置是影响减振效果的关键参数.气腔最优厚度主要由附面层厚度和实际振动频率决定,需结合实际情况确定气腔厚度,以最大程度降低振动响应;气腔初始压强越高,阻尼系数越大;吸振薄板的固有频率应尽可能与叶片本体接近,并且安装在本体振动响应最大位置,以取得最好的减振效果.      

基于经验模态分解的燃烧不稳定性分析

实验研究了在常温常压条件下贫燃预混旋流火焰的燃烧不稳定性,发生燃烧不稳定性时其压力脉动表现为非平稳信号.利用一种基于经验模态分解(EMD)的希尔伯特-黄变换(HHT)算法对在当量比分别为0.71和0.80工况下的压力脉动信号进行了时频分析.针对压力脉动信号进行经验模态分解,选取主要的固有模态函数(IMF),对IMF通过HHT变换得到瞬时频率并进行统计分析.结果表明:在当量比为0.71时,压力信号呈间歇式的脉动,其振型为拍振;在当量比为0.80时,脉动压力信号则呈现出极限环振型.在基于EMD的HHT变换中,IMF体现了燃烧不稳定性的固有模态且具有自适应性强的特点.      

带凸肩叶片的断裂故障分析

某型发动机风扇带凸肩的转子叶片发生断裂故障。断口分析表明其为疲劳裂纹特征,其疲劳源在叶盆侧凸肩工作面下侧靠近叶片前缘位置。根据微观分析结论,建立了风扇叶片三维实体模型,利用有限元方法分析了叶片的振动模态。结果表明：叶片在工作时,由于结构的激振可能发生某些阶次的共振,其应力分布与断口分析结果较一致,初步判断叶片是由于共振而发生了疲劳断裂。     

基于SP-ABC算法的数控铣削参数优化

针对铣削加工中成本最低的优化问题,采用一种改进的人工蜂群(SP-ABC)算法对铣削参数进行优化.在基本ABC算法的基础上,嵌入粒子群(PSO)算法,以提高算法的局部寻优能力.此外,不同于传统的单工序优化,建立的优化目标模型,在考虑实际生产过程中的各种约束条件下,可同时对粗、精两个阶段多道工序同步进行优化.计算机仿真结果表明,相较其他的基本算法,该算法能够找到更优的铣削参数组合,从而实现铣削加工过程的成本最低化.     

RFID技术在航空领域的应用研究

射频识别(RFID)技术现已广泛用于物流、金融、零售等各个行业.航空领域的RFID应用起步较晚,通过对RFID技术在飞机制造商、原始设备生产厂家(OEM)、航空公司的一些典型的应用案例的分析,提出RFID技术应用于航空领域所面临的挑战及必要性,为其未来航空业自动识别技术的发展指明了方向.